Some more about condensate 10-7
What is condensate?
- Steam that has been condensed back into water by either raising its pressure or lowering its temperature. Not to be confused with demineralized, de-ionized, make up, or softened water. When the condensate enters the boiler feed pump additional chemicals are added and the product is now called boiler feed water.
Where does condensate come from?
- Condenser hotwells, the bottom part of the condenser
- Steam traps. They trap steam in the lines and let the condensate drain through.
- Heat exchangers. Condensate must be removed to allow the heat transfer. The condensate flows to the bottom where the steam trap will open and allow the condensate to flow to the receiver. There must be a positive differential pressure between the heat exchanger and the condensate line so that the condensate will flow out of the heat exchanger. If the differential pressure is not there, a pump will have to be installed to remove the condensate.
- Or any other place that you are using steam.
- It will contribute to corrosion problems in the system. Especially the boiler.
- Boilers like a ph of somewhere between 10 and 11.
- Hot water is almost the perfect solvent. Give it enough time and it will dissolve anything. Remember that boilers have to last thirty years or more. This means that water has plenty of time to do its damage. It is the oxygen in the condensate that makes condensate a strong oxidizing agent that can attack metals.
- Some carbon seal faces can be attacked by high oxygen levels in the condensate.
- The more gases entrained in the condensate the more likely the pump will experience cavitation problems.
- The condensate temperature determines the amount of dissolved oxygen. You are trying to conserve the energy (temperature) that was added to the steam to keep the amount of dissolved oxygen down
The average level detected in condensate receivers is three parts per million. This is almost one thousand times greater than the five parts per billion level that can induce pitting corrosion.
How does oxygen get into the condensate system?
- Through the packing of condensate pumps. The stuffing box is under a negative pressure, and air that is one third oxygen, leaks in.
- Valves above the water line can introduce oxygen as the velocity of the water lowers the pressure at the valve stem.
- Flanges can have the same problem as valves.
- Oxygen is dissolved in makeup water that was added to the boiler because of condensate leaks.
- Pumps with built in repellers that create a negative pressure in the pump stuffing box.
How do you get rid of the dissolved oxygen?
- Add chemicals to convert it. Hydrazine is an example. You are adding hydrogen that will combine with the oxygen to form water.
- In nuclear applications it is common to add hydrogen to the system for the same reason. Hydrogen and oxygen will combine to form water in a neutron flux.
- Deaerate the condensate. This is normally done by heating the condensate with steam in a deaerating tank that is located close to the suction of the boiler feed pump.
- Convert to balanced, o-ring mechanical seals that will prevent air from coming into the stuffing boxes of condensate pumps through packing.
- Seal valves above the water line and pipe flanges to prevent air from entering the system.
- Carbon dioxide (CO2) will combine with water (H2O) to form Carbolic acid (H2CO3) that will lower boiler ph.
Where does the CO2 come from?
Mammals exhale CO2. It enters condensate and feed water:
- Through the packing in condnsate pumps that take a suction on hot wells
- Valves above the water line
Why do we have to use so much “make up” water in our boiler ?
- Because we lose so much of it.
- Condensate pump discharge recirculation lines that are trying to put a positive pressure on packing are a common source of condensate loss.
- Boiler blow down is a major problem. Some boilers run with a constant blow down because air that is entering the system is changing the pH of the water, causing chemical addition that increases the total solids, causing the need for additional blow down..
- Steam tools.
- Air ejectors that are used to create a vacuum in receivers etc.
- Steam traps that drain to the ground.
What are some methods for conserving condensate?
- The discharge recirculation line used with packed pumps is a big waste. Convert to a balanced o-ring seal and save a pile of condensate.
- Stop air from entering the system. The air is causing frequent boiler blowdowns. You can easily seal flanges, valves and rotating shafts.
- Do not drain steam traps to the ground. Collect it in a tank that can be pumped back into the system.
- If condensate is being circulated through the cooling jacket on a pump, make sure it is not being discharged to a drain. There is no reason it cannot be returned to the condensate system.
- If condensate is being circulated between dual mechanical seals, it is not a good idea to return it to the condensate system. There is too a high probability of contaminating the condensate with product leakage.
- On February 13, 2018